Report

1 images

Flat solar collector VIESSMANN VITOSOL 100-FM type SH1F

38,750 ₴

Other

Sunday 11:55

Україна

Київ Get directions →

вул. Стеценка, 14/44

27 views

Published 4 days ago by Solar-Tech

38,750 ₴

In Other category

вул. Стеценка, 14/44, Київ, Україна

Get directions →

27 item views

Vitosol 100-FM type SH1F - powerful flat collector with ThermProtect absorber-layer connection, for horizontal installation

The powerful flat collector Vitosol 100-FM, supplied in a silver-coloured frame, will become an ideal addition to any heating system. With an absorber area of 2.3 m² these collectors are suitable for consumers with various energy requirements.

On average over a year they cover up to 60 percent of the energy required for domestic hot water and provide heating support. Paired with a condensing boiler, thanks to the Sun’s free energy, you can save more than a third of the energy used for heating and domestic hot water over the year.

Advantages:

No surface overheating or steam formation at low heat output

High coverage percentage of heating support and domestic hot water demand through solar energy

Universal design for mounting on pitched or flat roofs, integrating into the roof or installation on the façade

Powerful flat collector with ThermProtect absorber-layer connection

Horizontal and vertical installation possible

The powerful flat collectors Vitosol 100-FM will become an ideal addition to any heating system. With an absorber area of 2.3 m² they are suitable for consumers with any level of demand.

Over the course of a year they cover up to 60 percent of the energy required for domestic hot water and contribute to heating. When working together with a condensing boiler, thanks to the Sun’s free energy, these collectors allow saving even a third of the energy required for heating and producing hot water during the year.

ThermProtect protects against overheating

The "smart" absorber layer protects the collectors from overheating. ThermProtect technology, patented by Viessmann, when reaching a certain temperature level blocks the collector from accepting further energy.

ThermProtect allows the Vitosol 100-FM to achieve higher performance compared to conventional collectors. When the limiting temperature is exceeded the crystalline structure of the absorbing layer changes, its heat output increases many times over, and the collector power decreases. As a result the so-called stagnation temperature becomes significantly lower, and steam does not form in the solar circuit.

As the collector temperature decreases, the crystalline structure returns to its original state. The absorber again absorbs more than 95 percent of the received solar energy, turning it into useful heat. Only a small portion - about five percent - is reflected back. Such changes in the crystalline structure can be repeated an unlimited number of times - the working qualities of the collector will not deteriorate.

Always tight and with high-quality thermal insulation

The aluminium frame, folded at the edges, and the seamless edging of the collector itself ensure long-term tightness and high structural stability. The collector back sheet is impact- and corrosion-resistant. High-quality thermal insulation significantly reduces heat losses, especially in cold weather.

Easy installation

The collectors are very easy to install. Built-in supply and return pipes allow reliable installation of large areas from many modules using a flexible stainless-steel plug connector. Up to twelve solar collectors are easily connected to each other.

Flat collectors are universal for mounting on roofs, for integration into the roof surface, or for installation in a raised position on flat roofs. Viessmann’s fast-mounting system consists of components that withstand static loads and are corrosion-protected, made of stainless steel and aluminium.

Technical specifications of the flat collector VIESSMANN VITOSOL 100-FM type SH1F:

Collector area, (m² )

2.51

Absorber area, (m²)

2.32

Optical, (efficiency %)

74.3

Size: WidthXHeightXDepth, (mm)

2380x1056x72

Mass without fluid, (kg)

Fluid/heat carrier volume, (l)

1.67

Permissible working pressure, (bar)

Max. stagnation temperature, (°C)

221

Connection, (Ø mm)

Number of connections

Frame material

aluminium

Absorber material

Copper

Absorber connection

laser welding

Coating material

tempered glass

Country of manufacture

Germany

Published on 2026/10/11

Description